Direct Burial Splice Covers #14 - 350 MCMDirect Burial Splice Covers #14 - 350 MCM features include: li>Our Direct Burial Splice Covers Can Be Used with a variety Connectors for Direct Burial, Underground Vault and Overhead Service Splices Rubber Cover Only - Connector Not Included No Taping, Heat Shrink or Mastic Required Approved for Aluminum or Copper Conductors or Connectors 600 Volt max REA Approved Order Qty of 1 = 1 Piece Below is more info on our Direct Burial Splice Covers #14 - 350 MC... read more

Direct Burial Splice Covers #14 - 350 MCMDirect Burial Splice Covers #14 - 350 MCM features include: li>Our Direct Burial Splice Covers Can Be Used with a variety Connectors for Direct Burial, Underground Vault and Overhead Service Splices Rubber Cover Only - Connector Not Included No Taping, Heat Shrink or Mastic Required Approved for Aluminum or Copper Conductors or Connectors 600 Volt max REA Approved Order Qty of 1 = 1 Piece Below is more info on our Direct Burial Splice Covers #14 - 350 MCM read less

150

read less

3M™ Motor Lead Pigtail Splicing Kits 5300 Series are designed for splicing motor lead cables to incoming feeder cables, including the accommodation of pigtail (stub) connections at 1000 volts and less. The splice’s main component, the slip-on lug cover, is made from EPDM rubber. Mastic strips are used for the moisture seal.These kits are designed to be used with copper compression, one-hole lugs. After being crimped onto the cables, the lugs are bolted together in a pigtail configuration, then i... read more

3M™ Motor Lead Pigtail Splicing Kits 5300 Series are designed for splicing motor lead cables to incoming feeder cables, including the accommodation of pigtail (stub) connections at 1000 volts and less. The splice’s main component, the slip-on lug cover, is made from EPDM rubber. Mastic strips are used for the moisture seal.These kits are designed to be used with copper compression, one-hole lugs. After being crimped onto the cables, the lugs are bolted together in a pigtail configuration, then insulated and sealed with the 3M Motor Lead Splicing Kit. Each kit makes three splices and contains the necessary materials (except lugs) needed to make three splices. The lugs must be purchased separately. 3M™ Scotchlok™ Copper Compression Lugs 30000 Series, or other UL listed copper lugs, can be used.Kit contents include:• (3) Pigtail lug covers• (3) Mastic sealing strips• (3) Locking pins (kits 5302–5304 only)• (3) Tubes of silicone grease• (1) Instruction sheet read less

The 3M Motor Lead Pigtail Splice Kit 5300 Series offers sturdy, EPDM rubber lug covers that easily s...150 read more

The 3M Motor Lead Pigtail Splice Kit 5300 Series offers sturdy, EPDM rubber lug covers that easily slip onto cables. After crimping the lugs onto the cables, they are bolted together in a pigtail configuration, then insulated and sealed. This kit has everything you need to make 3 splices, including pigtail lug covers, mastic sealing strips and tubes of silicone grease. This product is CSA Certified and RoHS 2011/65/EU Compliant?. read less

3M™ 5760 Series Cold Shrink Inline Splice Kit with 2131 compound, is designed for splicing shielded, 5/8 to 15 kV armored or non armored cables. It is used in cable trays, junction boxes and cable racks/hangers, as well as aerial and wet or dry locations.

3M™ 5760 Series Cold Shrink Inline Splice Kit with 2131 compound, is designed for splicing shielded, 5/8 to 15 kV armored or non armored cables. It is used in cable trays, junction boxes and cable racks/hangers, as well as aerial and wet or dry locations. read less

3M™ 5760 Series Cold Shrink Inline Splice Kits contain a resin that constructs a tough replacement f...150 read more

3M™ 5760 Series Cold Shrink Inline Splice Kits contain a resin that constructs a tough replacement for cable armor and/or a jacket. The cold shrink insulators offer electrical insulation while the tapes provide electrical shielding. The flexible jacketing resin helps the splice to bend easily with the cable and is suitable for cable tray bends. The resin is self curing, resists abrasion and moisture. RoHS 2011/65/EU Compliant. read less

3M™ Scotchcast™ 72 N Series Inline Splice Kit is a 1 kV rated, rigid body splice designed to join signal and control cables. It fits shielded or unshielded constructions of plastic or rubber jacketed cables. It is perfect for inline splicing of shielded or unshielded cables, underground systems, joining of cable reel ends, direct burial applications, repair of cable failures and dig ins.

3M™ Scotchcast™ 72 N Series Inline Splice Kit is a 1 kV rated, rigid body splice designed to join signal and control cables. It fits shielded or unshielded constructions of plastic or rubber jacketed cables. It is perfect for inline splicing of shielded or unshielded cables, underground systems, joining of cable reel ends, direct burial applications, repair of cable failures and dig ins. read less

3M™ Scotchcast™ 72 N Series Inline Splice Kit helps in sealing collars or splice body ends, and the...150 read more

3M™ Scotchcast™ 72 N Series Inline Splice Kit helps in sealing collars or splice body ends, and the jumper wire with clips offers solderless shield continuity on shielded cables. RoHS 2011/65/EU Compliant?. read less

Streetlighting In-Line Non-Fused Mechanical Breakaway Disconnect Kits - These Streetlighting In-Line Non-Fused Mechanical Breakaway Disconnect Kits are for Street and Parking Lot Lighting ApplicationsStreetlighting In-Line Non-Fused Mechanical Breakaway Disconnect Kits features include: Streetlighting In-Line Mechanical Breakaway Disconnect Kits Provide Electrical Disconnect when Light Pole is seperated from Base under Impact Designed for Use in StreetLight Hand Holes Completely Waterproofnbsp;... read more

Streetlighting In-Line Non-Fused Mechanical Breakaway Disconnect Kits - These Streetlighting In-Line Non-Fused Mechanical Breakaway Disconnect Kits are for Street and Parking Lot Lighting ApplicationsStreetlighting In-Line Non-Fused Mechanical Breakaway Disconnect Kits features include: Streetlighting In-Line Mechanical Breakaway Disconnect Kits Provide Electrical Disconnect when Light Pole is seperated from Base under Impact Designed for Use in StreetLight Hand Holes Completely Waterproofnbsp; Rubber Overmolded Insulated Body Ensures Installer Safety and Connector Integrity Fuse or Connecting Link Remains in Load Side of Light Pole When Seperated Range Taking Design Covers a Wide Range of Wire Sizes Thru .38" Diameter using a Stepped "ROCKET" Sealing Feature AL9CU Dual Rated for Both Copper and Aluminum Cables Eliminates the Need for Taping, Heat Shrink and other Labor Intensive Insulating Methods 30 Amp 600 Volts Kits Inlcude: EPDM Rubber Housing, Fuse Clips, Connecting Link(as Required), Silicone Lubricant. - Fuse Not Included Order Qty of 1 = 1 Piece Below is more info on our Streetlighting In-Line Non-Fused Mechanical Breakaway Disconnect Kits read less

150

read less

These kits are applicable for indoor and outdoor installations, including direct burial, aerial and submersible applications. Each kit requires at least 1 roll of 3M™ Armorcast Structural Material. For use with 3/C or 4/C Armor Power Cable (Teck-90) up to 1000 V.3M™ 3/C Armored Power Cable 5730 Series accommodates a full range of cable sizes from 14 AWG–750 kcmil. The overall jacket diameter ranges from 0.62–4.00 (16–10• mm). Notes:• Connectors are not included in the kit. Use only CSA certified... read more

These kits are applicable for indoor and outdoor installations, including direct burial, aerial and submersible applications. Each kit requires at least 1 roll of 3M™ Armorcast Structural Material. For use with 3/C or 4/C Armor Power Cable (Teck-90) up to 1000 V.3M™ 3/C Armored Power Cable 5730 Series accommodates a full range of cable sizes from 14 AWG–750 kcmil. The overall jacket diameter ranges from 0.62–4.00 (16–10• mm). Notes:• Connectors are not included in the kit. Use only CSA certified compression connectors. Vinyl or nylon butt connectors are preferred for 5730 and 5731 series. • Amount of armorcast needed is based on two half-lapped layers and 15’ rolls. read less

150

read less

3M™ Scotchcast™ Multi-Mold Resin Splice Kits 85 Series are a group of versatile splice kits for insulating and waterproofing odd-sized and odd-shaped splices in underground applications, up to 1000 volts. Splices may be inline, wye, X, butt and dead-end spliceconfigurations (for non-shielded cable) using split bolts, H tap or C tap compression connectors.

3M™ Scotchcast™ Multi-Mold Resin Splice Kits 85 Series are a group of versatile splice kits for insulating and waterproofing odd-sized and odd-shaped splices in underground applications, up to 1000 volts. Splices may be inline, wye, X, butt and dead-end spliceconfigurations (for non-shielded cable) using split bolts, H tap or C tap compression connectors. read less

3M™ Scotchcast™ Multi Mold Resin Splice Kit 85 Series includes a flexible film plastic mold, electri...150 read more

3M™ Scotchcast™ Multi Mold Resin Splice Kit 85 Series includes a flexible film plastic mold, electrical insulating resin 2104, pressure sensitive adhesive film sealing strip and a comprehensive instruction booklet. Using split bolts, H tap or C tap compression connectors, it provides inline, wye, X, butt and dead end splice configurations. It has a flexible film plastic mold with a built in porous spacer web for ensuring proper thickness of insulating compound. The splice kit is perfect for direct burial applications, underground systems, joining of cable reel ends, cable failures and dig ins. RoHS 2011/65/EU Compliant?. read less

3M™ 82 BF Series Resin Compression C Tap Cable Splice Kit with flame retardant compound 2131 is designed for tap splices on non shielded portable power cables and cords. This kit is suitable for use on single or multi conductor cables using a compression C tap connector. The tap splice can accommodate cables and cords that are rated up to 1 kV.

3M™ 82 BF Series Resin Compression C Tap Cable Splice Kit with flame retardant compound 2131 is designed for tap splices on non shielded portable power cables and cords. This kit is suitable for use on single or multi conductor cables using a compression C tap connector. The tap splice can accommodate cables and cords that are rated up to 1 kV. read less

3M™ 82 BF Series Resin C Tap Cable Splice Kit features smooth, tapered splice prevents cable hang up...150 read more

3M™ 82 BF Series Resin C Tap Cable Splice Kit features smooth, tapered splice prevents cable hang ups and splice end lifting. The flame retardant compound 2131 is a self curing resin that bonds to itself and modern cable jackets. RoHS 2011/65/EU Compliant and MSHA Approved. read less