$651.20 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design sized to fit Type MV-90 or Type MV-105 cables with copper, or aluminum conductor sizes ranging from 2 AWG-1000 kcmil (35-500 mm²).
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design sized to fit Type MV-90 or Type MV-105 cables with copper, or aluminum conductor sizes ranging from 2 AWG-1000 kcmil (35-500 mm²).
The cold shrink splice body is a one-piece molded design made of special formulated silicone rubbers...150
The cold shrink splice body is a one-piece molded design made of special formulated silicone rubbers, while the cold shrink jacketing is made of EPDM rubber for physical protection. Each splice manufactured is factory tested to provide reliability.The splices can be used with standard copper (Cu) or aluminum (Al/Cu) inline compression (crimp type) connectors, and can be used for size transitions within the listed kit size range. They are designed to exceed minimum industry test standards, and have a BIL rating of 150 kV (equal to a 25 kV voltage class). The 5513A, 5514A, 5515A and 5516A QS-III splices meet or exceed the 15 kV Voltage Class rating requirements of IEEE 404. Each kit makes one splice.Note: Cable sizes shown below are for standard insulation thickness. Final determining factor is cable insulation O.D.
- Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for feeder and distribution circuits, it transitions from shielded to neutral power cables and fits type MV-90 cables
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for feeder and distribution circuits, it transitions from shielded to neutral power cables and fits type MV-90 cables
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- UPC
- 055128534906
- UNSPSC
- 39121718
- Country of Origin
- USA
CPT-2-1/2-3M
$440.89 /ea
3M™ Cold Shrink Corrosion Protection Kit CPT Series are designed to provide a quick and easy method for protecting bulkhead termination connectors from the corrosive influences of wet and salt-fog installation environments.A CPT series assembly is an open-ended tubular rubber sleeve which is factory expanded and assembled onto a removable core. The core is removed after the assembly has been positioned for installation over a bulkhead terminator connector. Mastic strips are provided for sealing between NPT fitting threads and the enclosure in use (junction box, cabinet, panel board, etc.). CPT insulating sleeves are made of an EPDM rubber that contains no chlorides or sulfers.
| Attributed Data | Included |
|---|---|
| Cable Size | 1.97 in - 4.30 in Yes |
| Color | Black Yes |
| Type | Corrosion Protection Yes |
CPT-3-1/2-3M
$585.21 /ea
3M™ Cold Shrink Corrosion Protection Kit CPT Series are designed to provide a quick and easy method for protecting bulkhead termination connectors from the corrosive influences of wet and salt-fog installation environments.A CPT series assembly is an open-ended tubular rubber sleeve which is factory expanded and assembled onto a removable core. The core is removed after the assembly has been positioned for installation over a bulkhead terminator connector. Mastic strips are provided for sealing between NPT fitting threads and the enclosure in use (junction box, cabinet, panel board, etc.). CPT insulating sleeves are made of an EPDM rubber that contains no chlorides or sulfers.
| Attributed Data | Included |
|---|---|
| Cable Minimum Outside Diameter | 2.90 in Yes |
| Connector Maximum Installed Length | 13.50 in Yes |
| Connector Maximum Outside Diameter | 6.00 in Yes |
CPT-1-3M
$349.65 /ea
3M™ Cold Shrink Corrosion Protection Kit CPT Series are designed to provide a quick and easy method for protecting bulkhead termination connectors from the corrosive influences of wet and salt-fog installation environments.A CPT series assembly is an open-ended tubular rubber sleeve which is factory expanded and assembled onto a removable core. The core is removed after the assembly has been positioned for installation over a bulkhead terminator connector. Mastic strips are provided for sealing between NPT fitting threads and the enclosure in use (junction box, cabinet, panel board, etc.). CPT insulating sleeves are made of an EPDM rubber that contains no chlorides or sulfers.
| Attributed Data | Included |
|---|---|
| Cable Minimum Outside Diameter | 0.66 in Yes |
| Connector Maximum Installed Length | 4.80 in Yes |
| Connector Maximum Outside Diameter | 2.20 in Yes |
| Product Image |
|
|
|
|---|---|---|---|
|
CPT-2-1/2-3M
3M™ Cold Shrink Corrosion Protection Kit CPT Series are designed to provide a quick and easy method for protecting bulkhead termination connectors from the corrosive influences of wet and salt-fog installation environments.A CPT series assembly is an...
$440.89 / EA
|
CPT-3-1/2-3M
3M™ Cold Shrink Corrosion Protection Kit CPT Series are designed to provide a quick and easy method for protecting bulkhead termination connectors from the corrosive influences of wet and salt-fog installation environments.A CPT series assembly is an...
$585.21 / EA
|
CPT-1-3M
3M™ Cold Shrink Corrosion Protection Kit CPT Series are designed to provide a quick and easy method for protecting bulkhead termination connectors from the corrosive influences of wet and salt-fog installation environments.A CPT series assembly is an...
$349.65 / EA
|
|
| Attributed Data | |||
| Cable Minimum Outside Diameter | 0.66 in 0.66 in | 2.90 in 2.90 in | |
| Cable Size | 1.97 in - 4.30 in 1.97 in - 4.30 in | ||
| Color | Black Black | ||
| Connector Maximum Installed Length | 4.80 in 4.80 in | 13.50 in 13.50 in | |
| Connector Maximum Outside Diameter | 2.20 in 2.20 in | 6.00 in 6.00 in | |
| Type | Corrosion Protection Corrosion Protection | ||
| Add a product to the cart | Show more details | Show more details | Show more details |
Recently Viewed
-
CS-195+28x52
3M
3M™ Fire Barrier Composite Sheet CS-195+ is a lightweight intumescent firestop that combines four components into a single system to help slow the spr...
See more details -
-
ECLX071M
SIEMENS INDUSTRY, INC.
Siemens Low Voltage Residential Specialty Load Centers Miscellaneous Grounding bars (Al/Cu). Large connectors rated for (one 14-1/0, or 2-3 14-10), sm...
See more details -
-
5513A-3/0-CU
3M
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire sh...
See more details