.jpg)
.png)
Products
$754.90 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design sized to fit Type MV-90 or Type MV-105 cables with copper, or aluminum conductor sizes ranging from 2 AWG-1000 kcmil (35-500 mm²).
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design sized to fit Type MV-90 or Type MV-105 cables with copper, or aluminum conductor sizes ranging from 2 AWG-1000 kcmil (35-500 mm²).
The cold shrink splice body is a one-piece molded design made of special formulated silicone rubbers...150
The cold shrink splice body is a one-piece molded design made of special formulated silicone rubbers, while the cold shrink jacketing is made of EPDM rubber for physical protection. Each splice manufactured is factory tested to provide reliability.The splices can be used with standard copper (Cu) or aluminum (Al/Cu) inline compression (crimp type) connectors, and can be used for size transitions within the listed kit size range. They are designed to exceed minimum industry test standards, and have a BIL rating of 150 kV (equal to a 25 kV voltage class). The 5513A, 5514A, 5515A and 5516A QS-III splices meet or exceed the 15 kV Voltage Class rating requirements of IEEE 404. Each kit makes one splice.Note: Cable sizes shown below are for standard insulation thickness. Final determining factor is cable insulation O.D.
- Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for feeder and distribution circuits, it transitions from shielded to neutral power cables and fits type MV-90 cables
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for feeder and distribution circuits, it transitions from shielded to neutral power cables and fits type MV-90 cables
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- UPC
- 051128534847
- UNSPSC
- 26121649
- Country of Origin
- USA
- Type:
- Inline
- Voltage Rating:
- 15,000 V
- Cable Type:
- Longitudinally Corrugated (LC); Tape Shield; UniShield(R); Wire Shield
- Conductor Material:
- Copper
- Conductor Size:
- 1 AWG
- Connector:
- 10004
- Insulation OD Range:
- 0.64 - 1.01 Inch
- Number of Conductors:
- 1
- Product Technology:
- Cold Shrink
- Type:
- Inline
- Voltage Rating:
- 15,000 V
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC)...
$754.90 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
$754.90 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design sized to fit Type MV-90 or Type MV-105 cables with copper, or aluminum conductor sizes ranging from 2 AWG-1000 kcmil (35-500 mm²).
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design sized to fit Type MV-90 or Type MV-105 cables with copper, or aluminum conductor sizes ranging from 2 AWG-1000 kcmil (35-500 mm²).
The cold shrink splice body is a one-piece molded design made of special formulated silicone rubbers...150
The cold shrink splice body is a one-piece molded design made of special formulated silicone rubbers, while the cold shrink jacketing is made of EPDM rubber for physical protection. Each splice manufactured is factory tested to provide reliability.The splices can be used with standard copper (Cu) or aluminum (Al/Cu) inline compression (crimp type) connectors, and can be used for size transitions within the listed kit size range. They are designed to exceed minimum industry test standards, and have a BIL rating of 150 kV (equal to a 25 kV voltage class). The 5513A, 5514A, 5515A and 5516A QS-III splices meet or exceed the 15 kV Voltage Class rating requirements of IEEE 404. Each kit makes one splice.Note: Cable sizes shown below are for standard insulation thickness. Final determining factor is cable insulation O.D.
- Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for feeder and distribution circuits, it transitions from shielded to neutral power cables and fits type MV-90 cables
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for feeder and distribution circuits, it transitions from shielded to neutral power cables and fits type MV-90 cables
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- UPC
- 051128534816
- UNSPSC
- 26121649
- Country of Origin
- USA
- Type:
- Inline
- Voltage Rating:
- 15,000 V
- Cable Type:
- Longitudinally Corrugated (LC); Tape Shield; UniShield(R); Wire Shield
- Conductor Material:
- Aluminum; Copper
- Conductor Size:
- 2 AWG
- Connector:
- 20003
- Number of Conductors:
- 1
- Product Technology:
- Cold Shrink
- Type:
- Inline
- Voltage Rating:
- 15,000 V
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC)...
$754.90 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
$754.90 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design sized to fit Type MV-90 or Type MV-105 cables with copper, or aluminum conductor sizes ranging from 2 AWG-1000 kcmil (35-500 mm²).
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design sized to fit Type MV-90 or Type MV-105 cables with copper, or aluminum conductor sizes ranging from 2 AWG-1000 kcmil (35-500 mm²).
The cold shrink splice body is a one-piece molded design made of special formulated silicone rubbers...150
The cold shrink splice body is a one-piece molded design made of special formulated silicone rubbers, while the cold shrink jacketing is made of EPDM rubber for physical protection. Each splice manufactured is factory tested to provide reliability.The splices can be used with standard copper (Cu) or aluminum (Al/Cu) inline compression (crimp type) connectors, and can be used for size transitions within the listed kit size range. They are designed to exceed minimum industry test standards, and have a BIL rating of 150 kV (equal to a 25 kV voltage class). The 5513A, 5514A, 5515A and 5516A QS-III splices meet or exceed the 15 kV Voltage Class rating requirements of IEEE 404. Each kit makes one splice.Note: Cable sizes shown below are for standard insulation thickness. Final determining factor is cable insulation O.D.
- Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for feeder and distribution circuits, it transitions from shielded to neutral power cables and fits type MV-90 cables
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for feeder and distribution circuits, it transitions from shielded to neutral power cables and fits type MV-90 cables
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- UPC
- 051128534823
- UNSPSC
- 26121649
- Country of Origin
- USA
- Type:
- Inline
- Voltage Rating:
- 15,000 V
- Cable Type:
- Longitudinally Corrugated (LC); Tape Shield; UniShield(R); Wire Shield
- Conductor Material:
- Copper
- Conductor Size:
- 2 AWG
- Connector:
- 10003
- Number of Conductors:
- 1
- Product Technology:
- Cold Shrink
- Type:
- Inline
- Voltage Rating:
- 15,000 V
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC)...
$754.90 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
$1,332.86 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
The 3M™ Cold Shrink Splice Kit QS-2000T Series allows you to splice either single-conductor PILC cable to single-conductor PILC cable, or singleconductor PILC cable to single-conductor Poly/EPR cable. Because of the design of the splice, size transitions can also be accommodated rather easily. The 3M™ Cold Shrink Splice Kit QS-2000T Series meets the requirements of IEEE 404.
The 3M™ Cold Shrink Splice Kit QS-2000T Series allows you to splice either single-conductor PILC cable to single-conductor PILC cable, or singleconductor PILC cable to single-conductor Poly/EPR cable. Because of the design of the splice, size transitions can also be accommodated rather easily. The 3M™ Cold Shrink Splice Kit QS-2000T Series meets the requirements of IEEE 404.
This kit allows you to splice either single conductor PILC cable to single conductor PILC cable, or...150
This kit allows you to splice either single conductor PILC cable to single conductor PILC cable, or single conductor PILC cable to single conductor Poly/EPR cable. Because of the design of the splice, size transitions can also be accommodated rather easily. Each kit makes one single conductor splice.Use 3M™ Scotchlok™ Connectors 2000T Series with these splice kits. Each kit contains sufficient quantities of material to make one splice.Note: Cable sizes shown below are for standard insulation thickness. Final determining factor is cable insulation O.D.
- Oil stop tubes provide rejacketing and moisture-seal protection to the splice
- Resists water and eliminate the need of sweat lead
- Designed for PILC transition to the poly/EPR cable
- Rated for 15 kV applications
- Oil stop tubes provide rejacketing and moisture-seal protection to the splice
- Resists water and eliminate the need of sweat lead
- Designed for PILC transition to the poly/EPR cable
- Rated for 15 kV applications
- UPC
- 054007505464
- UNSPSC
- 26121649
- Country of Origin
- ITA
- Type:
- Inline PILC Transition
- Voltage Rating:
- 15,000 V
- Cable Type:
- PILC
- Conductor Size:
- "1 AWG, 1/0 AWG, 2 AWG, 2/0 AWG, 3/0 AWG, 4 AWG"
- Type:
- Inline PILC Transition
- Voltage Rating:
- 15,000 V
The 3M™ Cold Shrink Splice Kit QS-2000T Series allows you to splice either single-conductor PILC cable to single-conductor PILC cable, or singleconductor PILC cable to single-conductor Poly/EPR cable....
$1,332.86 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
$1,568.14 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
The 3M™ Cold Shrink Splice Kit QS-2000T Series allows you to splice either single-conductor PILC cable to single-conductor PILC cable, or singleconductor PILC cable to single-conductor Poly/EPR cable. Because of the design of the splice, size transitions can also be accommodated rather easily. The 3M™ Cold Shrink Splice Kit QS-2000T Series meets the requirements of IEEE 404.
The 3M™ Cold Shrink Splice Kit QS-2000T Series allows you to splice either single-conductor PILC cable to single-conductor PILC cable, or singleconductor PILC cable to single-conductor Poly/EPR cable. Because of the design of the splice, size transitions can also be accommodated rather easily. The 3M™ Cold Shrink Splice Kit QS-2000T Series meets the requirements of IEEE 404.
This kit allows you to splice either single conductor PILC cable to single conductor PILC cable, or...150
This kit allows you to splice either single conductor PILC cable to single conductor PILC cable, or single conductor PILC cable to single conductor Poly/EPR cable. Because of the design of the splice, size transitions can also be accommodated rather easily. Each kit makes one single conductor splice.Use 3M™ Scotchlok™ Connectors 2000T Series with these splice kits. Each kit contains sufficient quantities of material to make one splice.Note: Cable sizes shown below are for standard insulation thickness. Final determining factor is cable insulation O.D.
- Oil stop tubes provide rejacketing and moisture-seal protection to the splice
- Resists water and eliminate the need of sweat lead
- Designed for PILC transition to the poly/EPR cable
- Rated for 15 kV applications
- Oil stop tubes provide rejacketing and moisture-seal protection to the splice
- Resists water and eliminate the need of sweat lead
- Designed for PILC transition to the poly/EPR cable
- Rated for 15 kV applications
- UPC
- 054007505471
- UNSPSC
- 26121649
- Country of Origin
- ITA
- Type:
- Inline PILC Transition
- Voltage Rating:
- 15,000 V
- Cable Type:
- PILC
- Conductor Size:
- "250 AWG, 3/0 AWG, 350 kcmil, 4/0 AWG"
- Type:
- Inline PILC Transition
- Voltage Rating:
- 15,000 V
The 3M™ Cold Shrink Splice Kit QS-2000T Series allows you to splice either single-conductor PILC cable to single-conductor PILC cable, or singleconductor PILC cable to single-conductor Poly/EPR cable....
$1,568.14 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
$1,820.75 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
The 3M™ Cold Shrink Splice Kit QS-2000T Series allows you to splice either single-conductor PILC cable to single-conductor PILC cable, or singleconductor PILC cable to single-conductor Poly/EPR cable. Because of the design of the splice, size transitions can also be accommodated rather easily. The 3M™ Cold Shrink Splice Kit QS-2000T Series meets the requirements of IEEE 404.
The 3M™ Cold Shrink Splice Kit QS-2000T Series allows you to splice either single-conductor PILC cable to single-conductor PILC cable, or singleconductor PILC cable to single-conductor Poly/EPR cable. Because of the design of the splice, size transitions can also be accommodated rather easily. The 3M™ Cold Shrink Splice Kit QS-2000T Series meets the requirements of IEEE 404.
This kit allows you to splice either single conductor PILC cable to single conductor PILC cable, or...150
This kit allows you to splice either single conductor PILC cable to single conductor PILC cable, or single conductor PILC cable to single conductor Poly/EPR cable. Because of the design of the splice, size transitions can also be accommodated rather easily. Each kit makes one single conductor splice.Use 3M™ Scotchlok™ Connectors 2000T Series with these splice kits. Each kit contains sufficient quantities of material to make one splice.Note: Cable sizes shown below are for standard insulation thickness. Final determining factor is cable insulation O.D.
- Oil stop tubes provide rejacketing and moisture-seal protection to the splice
- Resists water and eliminate the need of sweat lead
- Designed for PILC transition to the poly/EPR cable
- Rated for 15 kV applications
- Oil stop tubes provide rejacketing and moisture-seal protection to the splice
- Resists water and eliminate the need of sweat lead
- Designed for PILC transition to the poly/EPR cable
- Rated for 15 kV applications
- UPC
- 054007505556
- UNSPSC
- 26121649
- Country of Origin
- ITA
- Type:
- Inline PILC Transition
- Voltage Rating:
- 15,000 V
- Cable Type:
- PILC
- Standard:
- IEEE-404-1993
- Type:
- Inline PILC Transition
- Voltage Rating:
- 15,000 V
The 3M™ Cold Shrink Splice Kit QS-2000T Series allows you to splice either single-conductor PILC cable to single-conductor PILC cable, or singleconductor PILC cable to single-conductor Poly/EPR cable....
$1,820.75 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
$1,173.88 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
3M™ Cold Shrink QS-III Inline Shielded Cable Splices 5524A, 5525A and 5526A Series are inline splices for joining 25/28 kV tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design.
3M™ Cold Shrink QS-III Inline Shielded Cable Splices 5524A, 5525A and 5526A Series are inline splices for joining 25/28 kV tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design.
The cold shrink splice body is a one-piece molded design made of specially formulated silicone rubbe...150
The cold shrink splice body is a one-piece molded design made of specially formulated silicone rubbers, while the jacketing is made of EPDM rubber for its special physical properties. Each splice is high-voltage production tested to ensure reliability. Kits can be ordered with connectors packed in the kit, or the kit and connector can be ordered as separate items. Meets requirements of IEEE 404.Each kit makes one splice.Note: Cable sizes shown below are for standard insulation thickness. Final determining factor is cable insulation O.D.
- Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for inline splicing, feeder and distribution circuits, size transition splicing, direct burial installations and submerged locations
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for inline splicing, feeder and distribution circuits, size transition splicing, direct burial installations and submerged locations
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- UPC
- 051128538463
- UNSPSC
- 26121649
- Country of Origin
- USA
- Type:
- Inline
- Voltage Rating:
- 25,000/28,000 V
- Cable Type:
- Longitudinally Corrugated (LC); Tape Shield; UniShield(R); Wire Shield
- Conductor Material:
- Copper; Copper/Aluminum
- Conductor Size:
- 250 kcmil
- Connector:
- 10009
- Number of Conductors:
- 1
- Product Technology:
- Cold Shrink
- Type:
- Inline
- Voltage Rating:
- 25,000/28,000 V
3M™ Cold Shrink QS-III Inline Shielded Cable Splices 5524A, 5525A and 5526A Series are inline splices for joining 25/28 kV tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shield...
$1,173.88 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
$687.55 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
3M™ Cold Shrink QS-III Inline CN/JCN Cable Splices 5456A-WG, 5457A-WG and 5458A-WG are inline splices for joining 25/28 kV jacketed concentric neutral (JCN) or concentric neutral (CN) power cables. It is a cold shrink design.
3M™ Cold Shrink QS-III Inline CN/JCN Cable Splices 5456A-WG, 5457A-WG and 5458A-WG are inline splices for joining 25/28 kV jacketed concentric neutral (JCN) or concentric neutral (CN) power cables. It is a cold shrink design.
The cold shrink splice body is a one-piece molded design made of specially formulated silicone rubbe...150
The cold shrink splice body is a one-piece molded design made of specially formulated silicone rubbers, while the jacketing is made of EPDM rubber for its special physical properties. Each splice is high-voltage production tested to ensure reliability. Kits can be ordered with connectors packed in the kit or the kit and connector can be ordered as separate items. Meets requirements of IEEE 404.Each kit makes one splice.Note: 5456A-WG, 5457A-WG and 5458A-WG are partially jacketed splices containing built-in bleeder wires. Additional end user materials are required to convert to full jacketing.Note: Cable sizes shown below are for standard insulation thickness. Final determining factor is cable insulation O.D.
- Inline splice for joining jacketed concentric neutral (JCN) and concentric neutral (CN) power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for feeder and distribution circuits, size transition splicing, direct burial installations, submerged locations and use with standard inline crimp connectors
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- Inline splice for joining jacketed concentric neutral (JCN) and concentric neutral (CN) power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for feeder and distribution circuits, size transition splicing, direct burial installations, submerged locations and use with standard inline crimp connectors
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- UPC
- 051128537497
- UNSPSC
- 26121649
- Country of Origin
- USA
- Type:
- Inline
- Voltage Rating:
- 15,000 V
- Cable Type:
- Concentric Neutral (CN); Jacketed Concentric Neutral (JCN)
- Conductor Material:
- Aluminum
- Conductor Size:
- 4/0 AWG
- Connector:
- 20008
- Insulation OD Range:
- 0.64 - 1.01 Inch
- Number of Conductors:
- 1
- Product Technology:
- Cold Shrink
- Type:
- Inline
- Voltage Rating:
- 15,000 V
3M™ Cold Shrink QS-III Inline CN/JCN Cable Splices 5456A-WG, 5457A-WG and 5458A-WG are inline splices for joining 25/28 kV jacketed concentric neutral (JCN) or concentric neutral (CN) power cables. It...
$687.55 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders