.jpg)
.png)
Products
$754.90 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design sized to fit Type MV-90 or Type MV-105 cables with copper, or aluminum conductor sizes ranging from 2 AWG-1000 kcmil (35-500 mm²).
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design sized to fit Type MV-90 or Type MV-105 cables with copper, or aluminum conductor sizes ranging from 2 AWG-1000 kcmil (35-500 mm²).
The cold shrink splice body is a one-piece molded design made of special formulated silicone rubbers...150
The cold shrink splice body is a one-piece molded design made of special formulated silicone rubbers, while the cold shrink jacketing is made of EPDM rubber for physical protection. Each splice manufactured is factory tested to provide reliability.The splices can be used with standard copper (Cu) or aluminum (Al/Cu) inline compression (crimp type) connectors, and can be used for size transitions within the listed kit size range. They are designed to exceed minimum industry test standards, and have a BIL rating of 150 kV (equal to a 25 kV voltage class). The 5513A, 5514A, 5515A and 5516A QS-III splices meet or exceed the 15 kV Voltage Class rating requirements of IEEE 404. Each kit makes one splice.Note: Cable sizes shown below are for standard insulation thickness. Final determining factor is cable insulation O.D.
- Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for feeder and distribution circuits, it transitions from shielded to neutral power cables and fits type MV-90 cables
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for feeder and distribution circuits, it transitions from shielded to neutral power cables and fits type MV-90 cables
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- UPC
- 051128534847
- UNSPSC
- 26121649
- Country of Origin
- USA
- Type:
- Inline
- Voltage Rating:
- 15,000 V
- Cable Type:
- Longitudinally Corrugated (LC); Tape Shield; UniShield(R); Wire Shield
- Conductor Material:
- Copper
- Conductor Size:
- 1 AWG
- Connector:
- 10004
- Insulation OD Range:
- 0.64 - 1.01 Inch
- Number of Conductors:
- 1
- Product Technology:
- Cold Shrink
- Type:
- Inline
- Voltage Rating:
- 15,000 V
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC)...
$754.90 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
Image colors may not be accurate.
Please see details, or call (800) 462-7733 for more
information.
$45.07 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
Unfortunately, we do not have a description available for 5100-20. Please call (800) 462-7733 for more information.
Unfortunately, we do not have a description available for 5100-20. Please call (800) 462-7733 for more information.
- UPC
- 048011083952
Unfortunately, we do not have a description available for 5100-20. Please call (800) 462-7733 for more information.
$45.07 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
Image colors may not be accurate.
Please see details, or call (800) 462-7733 for more
information.
$23.05 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
Unfortunately, we do not have a description available for 26001-3M. Please call (800) 462-7733 for more information.
Unfortunately, we do not have a description available for 26001-3M. Please call (800) 462-7733 for more information.
- UPC
- 051131260016
Unfortunately, we do not have a description available for 26001-3M. Please call (800) 462-7733 for more information.
$23.05 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
Image colors may not be accurate.
Please see details, or call (800) 462-7733 for more
information.
$304.44 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
Unfortunately, we do not have a description available for 01130-3M. Please call (800) 462-7733 for more information.
Unfortunately, we do not have a description available for 01130-3M. Please call (800) 462-7733 for more information.
- UPC
- 051131311251
Unfortunately, we do not have a description available for 01130-3M. Please call (800) 462-7733 for more information.
$304.44 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
$754.90 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design sized to fit Type MV-90 or Type MV-105 cables with copper, or aluminum conductor sizes ranging from 2 AWG-1000 kcmil (35-500 mm²).
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design sized to fit Type MV-90 or Type MV-105 cables with copper, or aluminum conductor sizes ranging from 2 AWG-1000 kcmil (35-500 mm²).
The cold shrink splice body is a one-piece molded design made of special formulated silicone rubbers...150
The cold shrink splice body is a one-piece molded design made of special formulated silicone rubbers, while the cold shrink jacketing is made of EPDM rubber for physical protection. Each splice manufactured is factory tested to provide reliability.The splices can be used with standard copper (Cu) or aluminum (Al/Cu) inline compression (crimp type) connectors, and can be used for size transitions within the listed kit size range. They are designed to exceed minimum industry test standards, and have a BIL rating of 150 kV (equal to a 25 kV voltage class). The 5513A, 5514A, 5515A and 5516A QS-III splices meet or exceed the 15 kV Voltage Class rating requirements of IEEE 404. Each kit makes one splice.Note: Cable sizes shown below are for standard insulation thickness. Final determining factor is cable insulation O.D.
- Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for feeder and distribution circuits, it transitions from shielded to neutral power cables and fits type MV-90 cables
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for feeder and distribution circuits, it transitions from shielded to neutral power cables and fits type MV-90 cables
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- UPC
- 051128534816
- UNSPSC
- 26121649
- Country of Origin
- USA
- Type:
- Inline
- Voltage Rating:
- 15,000 V
- Cable Type:
- Longitudinally Corrugated (LC); Tape Shield; UniShield(R); Wire Shield
- Conductor Material:
- Aluminum; Copper
- Conductor Size:
- 2 AWG
- Connector:
- 20003
- Number of Conductors:
- 1
- Product Technology:
- Cold Shrink
- Type:
- Inline
- Voltage Rating:
- 15,000 V
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC)...
$754.90 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
$754.90 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design sized to fit Type MV-90 or Type MV-105 cables with copper, or aluminum conductor sizes ranging from 2 AWG-1000 kcmil (35-500 mm²).
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design sized to fit Type MV-90 or Type MV-105 cables with copper, or aluminum conductor sizes ranging from 2 AWG-1000 kcmil (35-500 mm²).
The cold shrink splice body is a one-piece molded design made of special formulated silicone rubbers...150
The cold shrink splice body is a one-piece molded design made of special formulated silicone rubbers, while the cold shrink jacketing is made of EPDM rubber for physical protection. Each splice manufactured is factory tested to provide reliability.The splices can be used with standard copper (Cu) or aluminum (Al/Cu) inline compression (crimp type) connectors, and can be used for size transitions within the listed kit size range. They are designed to exceed minimum industry test standards, and have a BIL rating of 150 kV (equal to a 25 kV voltage class). The 5513A, 5514A, 5515A and 5516A QS-III splices meet or exceed the 15 kV Voltage Class rating requirements of IEEE 404. Each kit makes one splice.Note: Cable sizes shown below are for standard insulation thickness. Final determining factor is cable insulation O.D.
- Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for feeder and distribution circuits, it transitions from shielded to neutral power cables and fits type MV-90 cables
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
- Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
- Designed for feeder and distribution circuits, it transitions from shielded to neutral power cables and fits type MV-90 cables
- Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
- UPC
- 051128534823
- UNSPSC
- 26121649
- Country of Origin
- USA
- Type:
- Inline
- Voltage Rating:
- 15,000 V
- Cable Type:
- Longitudinally Corrugated (LC); Tape Shield; UniShield(R); Wire Shield
- Conductor Material:
- Copper
- Conductor Size:
- 2 AWG
- Connector:
- 10003
- Number of Conductors:
- 1
- Product Technology:
- Cold Shrink
- Type:
- Inline
- Voltage Rating:
- 15,000 V
The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC)...
$754.90 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
Image colors may not be accurate.
Please see details, or call (800) 462-7733 for more
information.
$149.10 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
3M™ Scotchlok™ High-Temperature Female Disconnect Terminal has dents and rolled edges for quick and easy disconnect. The terminal has a non-insulated, butted-seam barrel and withstands a maximum temperature of 900 degrees F (482 degrees C). Its steel construction offers durability and a nickel-plated finish resists corrosion.
3M™ Scotchlok™ High-Temperature Female Disconnect Terminal has dents and rolled edges for quick and easy disconnect. The terminal has a non-insulated, butted-seam barrel and withstands a maximum temperature of 900 degrees F (482 degrees C). Its steel construction offers durability and a nickel-plated finish resists corrosion.
3M™ Scotchlok™ High-Temperature Female Disconnect Terminal attaches to the mating part with a tongue...150
3M™ Scotchlok™ High-Temperature Female Disconnect Terminal attaches to the mating part with a tongue that slips over the male tab. It has a non-insulated, butted-seam barrel with a beveled mouth to easily guide the wire into position. RoHS 2011/65/EU Compliant.
- Non-insulated, butted-seam barrel with a beveled mouth offers easy insertion of wires
- Dents and rolled edges of this high-temperature female disconnect terminal offer excellent holding force
- Allows for quick and easy disconnect of wires
- Mates with 0.187-in wide male tab
- Non-insulated, butted-seam barrel with a beveled mouth offers easy insertion of wires
- Dents and rolled edges of this high-temperature female disconnect terminal offer excellent holding force
- Allows for quick and easy disconnect of wires
- Mates with 0.187-in wide male tab
- UPC
- 054007017622
- UNSPSC
- 31201502
- Country of Origin
- USA
3M™ Scotchlok™ High-Temperature Female Disconnect Terminal has dents and rolled edges for quick and easy disconnect. The terminal has a non-insulated, butted-seam barrel and withstands a maximum tempe...
$149.10 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
$28.15 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders
3M™ ScotchCode™ Wire Marker Tape Refill Roll SDR is available in ten NEMA colors, individual numbers and consecutive numbers, letters and symbols.
3M™ ScotchCode™ Wire Marker Tape Refill Roll SDR is available in ten NEMA colors, individual numbers and consecutive numbers, letters and symbols.
3M ScotchCode™ Wire Marker Tape Refill Roll SDR tape features a high tack, acrylic adhesive that res...150
3M ScotchCode™ Wire Marker Tape Refill Roll SDR tape features a high tack, acrylic adhesive that resists solvents, oil and water and adheres firmly to insulation surfaces. The SDR tape can be used for applications with operating temperatures between -40°F (-40°C) to 250°F (121°C).
- High tack, acrylic adhesive that resists solvents, oil and water and adheres firmly to insulation surfaces
- Available in ten NEMA colors, individualnumbers and consecutive numbers, letters and symbols
- Can be used forapplications with operating temperatures between -40°F (-40°C) to 250°F (121°C)
- High tack, acrylic adhesive that resists solvents, oil and water and adheres firmly to insulation surfaces
- Available in ten NEMA colors, individualnumbers and consecutive numbers, letters and symbols
- Can be used forapplications with operating temperatures between -40°F (-40°C) to 250°F (121°C)
- UPC
- 054007093794
- UNSPSC
- 39131508
- Country of Origin
- USA
- Material:
- Acrylic/Poyester
- Size:
- 0.215 inches x 96 inches
- Type:
- Tape Roll Refill
- Background Color:
- White
- Length:
- 96 in
- Material:
- Acrylic/Poyester
- Size:
- 0.215 inches x 96 inches
- Sub Brand:
- ScotchCode
- Temperature Rating:
- 32 to 120 F
- Type:
- Tape Roll Refill
- Width:
- 0.215 in
3M™ ScotchCode™ Wire Marker Tape Refill Roll SDR is available in ten NEMA colors, individual numbers and consecutive numbers, letters and symbols.
$28.15 / EA
In stock (0)
Lead time: over 7 days
may be longer on small orders